The Morpho carries 3.9 mm of blade stock at 61 HRC, two titanium handles, and a pivot built from parts Herman Knives makes on its own lathes. The washers alone go through a Swiss-type Citizen Cincom A20, a vacuum furnace, a Mitsubishi wire EDM and a hand lapping table before they reach 0.6 mm and a 4000-grit finish.
This is Bartosz Herman's first butterfly knife. His shop in Poland has built a following on small runs of titanium folders, and the Morpho takes that hardware into a format with two pivots instead of one. The listing went live at Polish Custom Knives on 3 November in a Damacore Tesseract half-dress build, one piece, available immediately.

| Spec | Morpho (Damacore half-dress) |
|---|---|
| Blade steel | Damacore Odin's Eye DC18N, core N11X, sides RWL-34 + PMC27 |
| Blade thickness | 3.9 mm / 0.1535 in |
| Hardness | 61 HRC, deep cryogenic treatment |
| Blade finish | Mirror polished |
| Handle | Grade 5 titanium, Tesseract pattern |
| Backspacer and clip | Grade 5 titanium, Tesseract pattern |
| Latch | Damasteel |
| Bearings | Caged ceramic, 16 balls |
| Washers | M390, 60 HRC, wire-EDM cut, hand lapped to 4000 grit |
| Pivot | 440C at 56-58 HRC, TORX T20, widened thread with reduced pitch |
| Stop pin | Tungsten carbide |
| Blade length | 4.17 in / 106 mm |
| Overall length | 9.76 in / 248 mm (5.47 in closed) |
| Weight | 5.19 oz / 147 g |
| Price | Not disclosed |
Two pivots make the small parts matter more
A folding knife has one pivot, so play shows up in one place. A balisong has two, and any slop in either handle gets multiplied once the knife is spinning. Herman's answer is a stack of parts most production balisongs do not carry: a tungsten carbide stop pin, a 440C pivot hardened to 56-58 HRC, and those M390 washers cut to 0.6 mm on a wire EDM.
The washers get 25 mm bar stock, vacuum heat treated to 60 HRC to cut internal stress, drilled on the lathe, then sliced on the wire machine so the bore stays concentric. Lapping by hand to 4000 grit removes the surface roughness the wire leaves behind. Herman states the point of the process plainly enough: a smoother washer means fewer deep scratches on the blade tang and less chance of cracking a ceramic ball.
- Bearing cage holds 16 ceramic balls and is designed to stop them migrating under load
- Pivot thread is wider in diameter and finer in pitch than a standard T20 part, so adjustment moves in smaller increments
- Lock side uses a titanium liner with a tungsten carbide insert on the Sting pattern; the Morpho build lists Grade 5 titanium throughout
Damacore up front, Damasteel at the latch
The blade is Damacore DC18N, a powder metallurgy damascus with an N11X core between RWL-34 and PMC27, taken to 61 HRC and polished to a mirror. Herman offers the Morpho across M390, M398, CPM MagnaCut, Damasteel RWL34 and Elmax depending on the configuration, and damascus variants on top of that, so the half-dress Damacore piece is the top of the range rather than the standard build.
Naming it after a Morpho butterfly is a design brief as much as a joke. The blue on those wings shifts with the angle of light, and a polished damascus blade under a moving handle does something similar. Whether that matters depends on whether the knife gets flipped or carried.
Herman does not publish a price for the model, and the single unit at Polish Custom Knives is the only one listed at the time of writing. Custom balisongs from European makers have never been a volume business, and a build that includes in-house washers, a custom pivot and a Damasteel latch is not going to be priced against a production trainer.
The adjustment on this one takes a TORX T20 key, and turning it moves the handles in finer steps than the hardware most balisongs ship with.